Forklift mast parts guide
Forklift Mast Lift Chains: References, Inspection and Replacement Decisions
A mast chain carries the lifting force between the lift cylinder, chain anchors, rollers and fork carriage. Chain pitch, plate arrangement, length, end fittings and mast configuration must agree with the truck. A chain that looks similar or is described only by forklift capacity is not a confirmed replacement.
Mast Lift Chain
Part No. 162357Reference shown for a 2–2.5 t triplex mast configurationRequest a verified quote
Mast Lift Chain
Part No. 162377Reference shown for a 2–2.5 t triplex mast configurationRequest a verified quote
Mast Lift Chain
Part No. 163481Reference shown for a 3.5–3.8 t triplex mast configurationRequest a verified quoteWhere the chain works
Lift chains run over mast sheaves and connect the cylinder or fixed anchor points to the fork carriage. Duplex, triplex and free-lift masts use different chain paths and lengths.
Why capacity alone is insufficient
Two trucks with the same rated capacity can use different mast heights, chain pitches, plate counts, anchor fittings or production versions. Confirm the truck and mast before ordering.
What proves the reference
Use the chain reference, forklift model and serial number, mast type, closed and extended mast height, chain markings, end fittings and clear photographs of the full chain route.
Inspection points that matter
| Elongation | Measure chain wear using the method and allowable limit specified for the truck or chain. Visual appearance alone cannot confirm elongation. |
|---|---|
| Plates and pins | Look for cracked plates, turned or protruding pins, corrosion, stiff joints and impact damage. A cracked or structurally damaged chain is not repaired by welding. |
| Anchors and sheaves | Inspect anchor bolts, clevises, sheaves, bearings and alignment. A new chain fitted to damaged or misaligned hardware can wear quickly. |
| Lubrication | Use the lubricant and interval specified by the truck or chain manufacturer. Clean off abrasive contamination before lubrication; do not use a method that forces dirt into the joints. |
| Chain pair | Where the mast uses paired chains, compare both sides for length, tension and wear. Follow the manufacturer’s rule on replacing chains as a matched set. |
Workshop judgment: uneven carriage height or noisy lifting is not automatically a chain fault. Chain adjustment, mast rollers, sheaves, anchors, cylinder movement and carriage alignment must be checked together.
Genuine, identifiable OEM and lower-cost replacements
Genuine chain references are the safest choice when mast data is incomplete or fleet policy requires traceable original parts. An identifiable OEM-quality chain can be considered when pitch, plate construction, tensile specification, length and end fittings are documented. A low price without material, construction and traceability information is a poor basis for a load-bearing component.
Market prices change with chain size, total length, end fittings, supply level and whether the quotation covers one chain or a matched pair. Online prices are not comparable until those details agree.
Information required for a chain quotation
Send the forklift model and serial number, mast type and height, existing chain number or markings, photographs of both end fittings and chain route, required quantity and any measured wear information.
Verified forklift replacement part
162357 2-2.5T Triplex Mast Lift Chain
2-2.5T Triplex Mast Lift Chain reference 162357 is shown with an actual product photo to make identification easier.
Authpart checks the reference together with the available truck and component information before quotation. This helps prevent ordering a part that looks similar but cannot be installed or used correctly.
Verify This Part for My Forklift
Product overview
| Product | 2-2.5T Triplex Mast Lift Chain |
|---|---|
| Reference / specification | 162357 |
| System | Forklift mast and lifting system |
| Supply option | Brand and supply option stated clearly in our quotation |
| Application | Confirmed from the available truck and component information |
Why the correct match matters
Mast parts must match the truck capacity, mast type and lifting arrangement. Chain pitch, length, fork class and mounting dimensions vary between mast configurations.
Reference first
We check 162357 instead of quoting from a general description alone.
Truck confirmation
The model, serial number and component details help us confirm the correct version.
Visible order check
Reference labels and product condition can be photographed for confirmation before shipment.
Send what you have
Send the part number, nameplate or clear photos you have. Our parts team will check the reference against the truck details and tell you exactly what else is needed.
- Truck capacity and mast type
- Part reference
- Critical dimensions and photos
Confirm 162357 before you order
Send the reference, truck model or clear product photos. Authpart will check the details and explain the proposed supply option clearly.
Request a Verified Quote